Ⅰ 555 timer design

The 555 timer is designed for Signiitik by Hans R. Camenzind in 1971. Signiitke later was later acquired by Philips. Due to its easy-to-use, low price, and good reliability, it is still widely used in the design of electronic circuits today. Many manufacturers produce 555 chips, including traditional models of bipolar transistors and versions of CMOS design. 555 is considered to be one of the highest-output chips, with about 1 billion yields in 2003.

Different manufacturers have different structures, standard 555 chips integrate 25 transistors, 2 diodes, and 15 resistors, and 8 leads (DIP-8 packages). The derived model of 555 includes 556 (integrated with two 555 DIP-14 chips) and 558 and 559.

555 pin

The NE555 operating temperature range is 0-70 ° C, and the working temperature of the military-grade SE555 is -55 to +125 ° C. The 555 packages are divided into the high-reliability metal package (represented by T) and a low-cost epoxy resin package (represented by V), so 555's full label is NE555V, NE555T, SE555V, and SE555T. The source of the 555 chip name is generally considered to be three 5kΩ resistors, but Hans Camenzind denied this saying and said that the name was randomly selected.

There are also low-power versions, including 7555 and the TLC555. The power consumption of 7555 is lower than the standard 555 timers, and its manufacturer claims that the 7555 control pin is not like a ground capacitor like other 555 chips. And no noise decoupling capacitors are eliminated between the power supply and the ground.

Ⅱ 555 timer pin

The 555 chip of the DIP package is shown in the following table:

Ⅲ 555 timer internal structure

555 Timer is a mid-scale integrated circuit combined with analog circuit and digital circuit, and its internal structure is as shown below.

555 timer circuit

It consists of a partial part of a voltage divider, a comparator, a substantially R-S flip-flop, and a discharge tripode. The divider is formed by three 5kΩ equivalent resistors. The voltage divider provides the reference voltage to the comparator A1, A2, and the reference voltage of the comparator A1 is applied to the same phase input, and the reference voltage of the comparator A2 is added to the inverting input. The comparator consists of the same integrated op-amp A1, A2 as the two structures. The high-level trigger signal is added to the inverting input of the A1, and after comparing the reference voltage of the same phase input, the result is an input signal of the basic R-S flip-flop terminal; the low-level trigger signal is added to the same phase input of A2. After the reference voltage is compared with the inverting input, the result is an input signal of the basic R-S flip-flop end. The output state of the basic R-S flip-flop is controlled by the output of comparators A1 and A2.

Ⅳ 555 timer uses

555 timer can work in three working modes:

Single stability mode: In this mode, the 555 function is a single trigger. Applications include timers, pulse loss detection, rebound, tuning switches, divider, capacitance measurement, pulse width modulation (PWM), and the like.

No steady-state mode: In this mode, 555 works in the way in the oscillator. The 555 chip in this working mode is often used in a frequency flash lamp, a pulse generator, a logic circuit clock, a tone generator, a pulse position modulation (PPM). If the thermistor is used as a timing resistor, 555 can constitute a temperature sensor, and the frequency of the output signal is determined by the temperature.

Double steady-state mode (or Schmitt trigger mode): In the case where the DIS pin is vacant and the capacitor is not connected. The 555 work mode is similar to an RS trigger, which can be used to constitute a latching switch.

1.Single stability mode

In the single-stable mode of operation, the 555 timer operates as a single trigger pulse generator. When the input voltage drops to 1/3 of the VCC, the output pulse is output. The output pulse width depends on the time constant of the RC network consisting of the timing resistor and the capacitor. The output pulse stops when the capacitor voltage rises to 2/3 of the VCC. The pulse width can be adjusted by changing the time constant of the RC network based on actual needs.

The output pulse width t, that is, the time required for the capacitance-voltage charges to the VCC, is given by the following formula:

Although the capacitor is generally considered to discharge the OC gate when the capacitor voltage charges to the VCC, it takes a period of time to discharge, which is called "relaxation time" for a period of time. In practical applications, the cycle of triggering sources must be greater than the sum of relaxation time and pulse width (actually grows much in engineering applications).

2.Double steady mode

555 chip in the dual steady-state mode is similar to the basic RS trigger. In this mode, triggering pin (pin 2) and reset pin (pin 4) pass through the pull-up power to high, the threshold pin (pin 6) is directly grounded, the control pin (pin 5) ground through a small capacitor (0.01 to 0.1 μF),  and the discharge pin (pin 7) floating. Therefore, when pin 2 is input high (misleading low) voltage, the output is set, and the reset is output when pin 4 is grounded.

3.No steady mode

The 555 timers can output the square wave of a continuous specific frequency in an uncondensed operating mode. Resistor R1 is connected between VCC and discharge pin (pin 7), and another resistor (R2) is connected between pin 7 and the trigger pin (pin 2), pin 2, and threshold pin (pin 6) short. When the capacitor is charged to 2 / 3VCC through R1 and R2, then the output voltage is flipped, the capacitor is discharged to 1 / 3Vcc by R2, and then the capacitor is recharged, the output voltage is turned again.

For bipolar type 555, if the use of small R1 can cause the OC door to be saturated at the time of discharge so that the low power level time of the output waveform is much larger than the result of the above calculation.

In order to obtain a rectangular wave of less than 50% of the duty cycle, it can be implemented by parallel a diode to R2. This diode is turned on, shorted R2 so that the power supply is only charged only by R1; and when the discharge is turned off to achieve the effect of reducing the charging time to reduce the duty cycle.

Ⅴ 555 timer parameters

The following are the electrical parameters of the NE555, and the 555 timers of other different specifications may have different parameters, please check the datasheet.

Ⅵ Derivative chip of 555 timer

555 Timers have many different models produced by different companies, with different types of pins, and CMOS design. Some chips include several integrated 555 timers. Some other models of the 555 chip family are as follows: