4.5V to 5.5V, -40ºC to +85ºC, DC to 70 MIPS

4.5V to 5.5V, -40ºC to +125ºC, DC to 60 MIPS

4.5V to 5.5V, -40ºC to +150ºC, DC to 40 MIPS

Code-Efficient (C and Assembly) Architecture

Two 40-Bit Wide Accumulators

Single-Cycle (MAC/MPY) with Dual Data Fetch

Single-Cycle, Mixed-Sign MUL plus Hardware Divide

32-Bit Multiply Support

Provides a boot Flash segment in addition to the existing general Flash segment

Error Code Correction (ECC) for Flash

Added Two Alternate Register Sets for Fast Context Switching

Up to Six Pulse-Width Modulation (PWM) Outputs (three generators)

Primary Master Time Base Inputs allow Time Base Synchronization from Internal/External Sources

Dead Time for Rising and Falling Edges

8.3 ns PWM Resolution at 60 MIPS,

16.6 ns Center-Aligned mode at 60 MIPS

PWM support DC/DC, AC/DC, inverters, Power Factor Correction (PFC) and lighting

PWM support Brushless Direct Current (BLDC), Permanent Magnet Synchronous Motor (PMSM), AC Induction Motor (ACIM), Switched Reluctance Motor (SRM)

Programmable Fault inputs

Flexible trigger configurations for Analog-to-Digital conversion

Independent Time Base

Supports PWM lock, PWM output chopping and dynamic phase shifting

ADC configurable as 10-bit, 1.1 Msps with four S&H or 12-bit, 500 ksps with one S&H

Up to 36 analog inputs

Flexible and Independent ADC Trigger Sources

Up to Four Op Amp/Comparators with Direct Connection to the ADC module:

Additional dedicated comparator and 7-bit Digital-to-Analog Converter (DAC)

Programmable references with 128 voltage points

Programmable blanking and filtering

Supports mTouch™ capacitive touch sensing

Provides high-resolution time measurement (1 ns)

On-chip temperature measurement

Temperature sensor diode

Multiple sources of edge input triggers

Up to nine general purpose timers

Five 16-bit or up to two 32-bit timers/counters, Timer3 can provide ADC trigger

Oscillator Frequency Monitoring through CTMU

Four Output Capture modules configurable as timers/counters

Four Input Capture modules

Support for LIN/J2602 bus support and IrDA®

High and low speed (SCI)

25 Mbps data rate without PPS used

One I2C™ module (up to 1 Mbaud) with SMBus Support

Two SENT J2716 (Single Edge Nibble Transmission-Transmit/Receive) module for Automotive Applications

4-Channel DMA with User-Selectable Priority Arbitration

Universal Asynchronous Receiver/Transmitter (UART), Serial Peripheral Interface (SPI), ADC, Input Capture, Output Compare

AEC-Q100 Grade 1 (-40ºC to +125ºC)

AEC-Q100 Grade 0 (-40ºC to +150ºC)

Class B Safety Library, IEC 60730

ASIL-B & ASIL-C focused applications

FMEDA and Safety manual available under NDA upon request to your sales office

Safety qualified XC16 compiler

Flash with Error Correction Code (ECC)

CodeGuard™ Memory Protection

On-chip Regulator for CPU

Backup FRC and redundant clock sources

Fail Safe Clock Monitor

Windowed Watchdog Timer (WDT)

Windowed Deadman Timer (DMT)

Oscillator Frequency Monitoring through CTMU (OSCI, SYSCLK, FRC, BFRC, LPRC)

BOR and POR

Analog peripherals redundancies

Cyclical Redundancy Check (CRC)

Illegal Opcode Detection

PWM Lock and Dedicated PWM Fault Pin

Internal Loopback to test communication peripherals and IO ports

SFR and Configuration Locks

Address Trap

Math Error Trap

Redundant data storage for Flash-based Configuration bits and Peripheral Pin Select (PPS) Configuration bits