Arm Cortex-M33 processor, running at a frequency of up to 150 MHz

TrustZone, Floating Point Unit (FPU) and Memory Protection Unit (MPU)

Arm Cortex-M33 built-in Nested Vectored Interrupt Controller (NVIC)

Non-maskable Interrupt (NMI) input with a selection of sources

Arm Cortex-M33 co-processor

CASPER Crypto co-processor to enable hardware acceleration for certain asymmetric cryptographic algorithms

PowerQuad hardware accelerator for (fixed and floating point) DSP functions

Up to 640 KB on-chip flash program memory with a flash accelerator and 256-byte page erase and write

Up to 320 KB total SRAM consisting of 288 KB on the system bus and 32 KB on Core Bus

Arm TrustZone enabled

PRINCE module for real-time encryption of data being written to on-chip flash and decryption of encrypted flash data during reading to allow asset protection

AES-256 encryption/decryption engine

Secure Hash Algorithm (SHA2) module supporting secure boot with dedicated DMA controller

Physical Unclonable Function(PUF) using dedicated SRAM for silicon fingerprint. PUF can generate, store, and reconstruct key sizes from 64 to 4096 bits. Includes hardware for key extraction

Random Number Generator (RNG)

128-bit unique device serial number for identification (UUID)

Secure GPIO

Flexcomm Interface contains up to nine serial peripherals. Each Flexcomm Interface can be selected by software to be a USART, SPI, I2C, and I2S interface

I2C-bus interfaces support Fast-mode and Fast-mode Plus with data rates of up to 1Mbit/s and with multiple address recognition and monitor mode

USB 2.0 full speed host/device controller with on-chip PHY and dedicated DMA controller supporting crystal-less operation in device mode

USB 2.0 high-speed host/device controller with on-chip high-speed PHY

DMA0 controller with 23 channels and up to 22 programmable triggers, able to access all memories and DMA-capable peripherals.

DMA1 controller with 10 channels and up to 16 programmable triggers, able to access all memories and DMA-capable peripherals

Secured digital input/output (SD/MMC and SDIO) card interface with DMA support. SDIO with support for up to two cards. Supported card types are MMC, SDIO, and CE-ATA. Supports SD2.0, and SR25

CRC engine block can calculate a CRC on supplied data using one of three standard polynomials with DMA support.

Up to 64 General-Purpose Input/Output (GPIO) pins.

GPIO registers are located on the AHB for fast access. The DMA supports GPIO ports.

Up to eight GPIOs can be selected as Pin Interrupts (PINT), triggered by rising, falling or both input edges.

Two GPIO Grouped Interrupts (GINT) enable an interrupt based on a logical (AND/OR) combination of input states.

I/O pin configuration with support for up to 16 function options.

Programmable Logic Unit (PLU) to create small combinational and/or sequential logic networks including state machines

16-bit ADC with five differential channel pair (or 10 singled-ended channels), and with multiple internal and external trigger inputs and sample rates of up to 1.0MSamples/sec. The ADC supports two independent conversion sequences

Integrated temperature sensor connected to the ADC

Comparator with five input pins and external or internal reference voltage

Five 32-bit standard general purpose asynchronous timers/counters, which support up to four capture inputs and four compare outputs. Specific timer events can be selected to generate DMA requests

One SCTimer/PWM with eight input and ten output functions (including capture and match). Inputs and outputs can be routed to or from external pins and internally to or from selected peripherals. Internally, the SCTimer/PWM supports 16 match/captures, 16 events, and 32 states

32-bit Real-time clock (RTC) with 1 s resolution running in the always-on power domain. A timer in the RTC can be used for wake-up from all low power modes including deep power-down, with 1 ms resolution

Multiple-channel multi-rate 24-bit timer (MRT) for repetitive interrupt generation at up to four programmable, fixed rates

Windowed Watchdog Timer (WWDT) with FRO 1 MHZ as a clock source

Micro-Tick Timer running from the watchdog oscillator can be sued to wake-up the device from sleep and deep-sleep modes

42-bit free running OS Timer as continuous time-base for the system, available in any reduced power modes.

Internal Free Running Oscillator (FRO). This oscillator provides a selectable 96 MHz output, and a 12 MHz output (divided down from the selected higher frequency) that can be used as a system clock. The FRO is trimmed to +/- 1% accuracy over the entire voltage and temperature range

32 kHz Internal Free Running Oscillator FRO. The FRO is trimmed to +/- 1% accuracy over the entire voltage and temperature range

Internal low power oscillator (FRO 1 MHz)

Crystal oscillator with an operating frequency of 1 MHz to 25 MHz. Option for external clock input (bypass mode) for clock frequencies of up to 25 MHz