The bq25898, bq25898D are highly-integrated 4-A switch-modebattery charge management and system power path management devices for single cell Li-Ion andLi-polymer battery. The devices support high input voltage fast charging.

The low impedance power path optimizes switch-mode operation efficiency, reduces batterycharging time and extends battery life during discharging phase. The I2CSerial interface with charging and system settings makes the device a truly flexiblesolution.

The bq25898/98D is a highly-integrated 4-A switch-mode battery charge management andsystem power path management device for single cell Li-Ion and Li-polymer battery. It features fastcharging with high input voltage support for a wide range of smartphone, tablet and portabledevices. Its low impedance power path optimizes switch-mode operation efficiency, reduces batterycharging time and extends battery life during discharging phase. It also integrates Input CurrentOptimizer (ICO) and Resistance Compensation (IRCOMP) to deliver maximum charging power to battery.The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switchingFET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between systemand battery. It also integrates the bootstrap diode for the high-side gate drive and batterymonitor for simplified system design. The I2C serial interface withcharging and system settings makes the device a truly flexible solution.

The device supports a wide range of input sources, including standard USB host port, USBcharging port, and USB compliant adjustable high voltage adapter. To support fast charging usingadjustable high voltage adapter, the bq25898D provides support forMaxCharge handshake using D+/D- pins and DSEL pinfor USB switch control. In addition, both bq25898D and bq25898 include interface to supportadjustable high voltage adapter using input current pulse protocol. To set the default inputcurrent limit, device uses the built-in USB interface (bq25898D) or takes the result from detectioncircuit in the system (bq25898), such as USB PHY device. The device is compliant with USB 2.0 andUSB 3.0 power spec with input current and voltage regulation. In addition, the Input CurrentOptimizer (ICO) supports the detection of maximum power point detection of the input source withoutoverload. The device also meets USB On-the-Go (OTG) operation power rating specification bysupplying 5 V (Adjustable 4.5V-5.5V) on VBUS with current limit up to 2.4 A.

The power path management regulates the system slightly above battery voltage but doesnot drop below 3.5V minimum system voltage (programmable). With this feature, the system maintainsoperation even when the battery is completely depleted or removed. When the input current limit orvoltage limit is reached, the power path management automatically reduces the charge current tozero. As the system load continues to increase, the power path discharges the battery until thesystem power requirement is met. This operation prevents overloading the input source.

The device initiates and completes a charging cycle without software control. Itautomatically detects the battery voltage and charges the battery in three phases:pre-conditioning, constant current and constant voltage. At the end of the charging cycle, thecharger automatically terminates when the charge current is below a preset limit in the constantvoltage phase. When the full battery falls below the recharge threshold, the charger willautomatically start another charging cycle.

The charger provides various safety features for battery charging and system operations,including battery temperature negative thermistor monitoring, charging safety timer andovervoltage/overcurrent protections. The thermal regulation reduces charge current when thejunction temperature exceeds 120°C (programmable). The STAT output reports the charging status andany fault conditions. The PG output (bq25898) indicates if a good powersource is present. The INT immediately notifies host when fault occurs.

The device also provides a 7-bit analog-to-digital converter (ADC) for monitoring chargecurrent and input/battery/system (VBUS, BAT, SYS, TS) voltages. The QON pin provides BATFETenable/reset control to exit low power ship mode or full system reset function.

The devices are available in a 42-ball, 2.8 mm x 2.5 mm DSBGA package.

Feature

BQ2000PWR

BQ2000SN-B5TRG4

BQ2000TPWR

BQ2002DSNTR

BQ2004EPN

BQ2004HSNTR

BQ2004SNTR

BQ2005PN

BQ2005STR

BQ2010SN-0D107TR1

BQ2022ADBZR

BQ2053-D

BQ2054SNTRG4

BQ2057CTSTR

BQ2057DGKR

BQ2057WSNTR

BQ2058RSN-C5TR

BQ2060A-E619DBQR

BQ2085DBT

BQ21040DBVR

BQ24010DRCR

BQ24012DRCR

BQ24040DSQR

BQ24072RGTR

BQ24072RGTT

BQ24085DRCR

BQ24104RHLR

BQ24105RHLR

BQ24133RGYR

BQ24157YFFR

BQ24168YFFR

BQ24172RGYR

BQ24230RGTR

BQ24230RGTT

BQ24250RGER

BQ24296RGER

BQ24314DSGR

BQ24316DSGR

BQ24400PWR

BQ24610RGER

BQ24702PWR

BQ24737RGRR

BQ24738RGRR

BQ24751RHDR

BQ25050DQCR

BQ25700ARSNR

BQ25886RGER

BQ25892RTWR

BQ25898YFFR

BQ26200PWR

BQ26231PWR

BQ26500PWR

BQ26501PWR

BQ27510DRZR

BQ29310PWR

BQ29400PWR

BQ29410PWR

BQ29412PWR